Holley Steering Shaft Kit - 3rd Generation GM C10 Truck (Late)
| Application |
1979-1987 GM C10 Trucks |
| Brand |
Holley |
| Category |
Steering |
| 17 |
Black |
| Emission Code |
5 |
| 1727 |
DD |
| 1728 |
DD |
| 200 |
Black E-Coat |
| 3390 |
Performance |
| 10 |
Steel |
| 30 |
Yes |
| part type |
Steering Shaft |
| Product Type |
Steering Shafts |
| Sub Category |
Steering, Gear and Related Components |
| 2343 |
Yes |
| Warning |
California Proposition 65 |
| Description_INV |
3RD GEN C10 STEERING SHAFT 1979-1987 |
| Description_ASC |
It is extremely important that these steering shafts are installed by a qualified technician. Failing to do so will result in an unsafe vehicle.If installing these shafts with an OE steering box, you may need to trim the pin on the input shaft for U-joint clearance.Loctite 242, extra grease, and a torque wrench are highly recommended!!! |
| Description_DES |
Holley Steering Shaft Kit - 3rd Generation GM C10 Truck (Late) |
| Description_EXT |
Fits 1979-1987 GM C10 Trucks |
| Description_MKT |
These Holley steering shaft kits were designed to replace a worn stock one on your latter years' 3rd generation GM C10 trucks or with an engine swap where additional clearance may be needed. With sturdy DD-style steel shafts and dual u-joints, there is plenty of adjustability for your project to ensure everything is exact and safe. |
| Description_MKT |
*See Holley Part # 320-322 for 1973-1978 C10 Steering Shaft |
| Description_FAB |
Complete bolt-on solution with little or no modifications necessary depending on use |
| Description_FAB |
Eliminates factory rag joint providing a precise and responsive steering input |
| Description_FAB |
Will also work as a factory replacement steering shaft |
| Description_FAB |
E-Coat for maximum protection against corrosion |
| Description_FAB |
Steel construction with retaining screws on the bearing caps for strength and durability |
| Description_INV |
3RD GEN C10 STEERING SHAFT 1979-1987 |
| Description_ASC |
It is extremely important that these steering shafts are installed by a qualified technician. Failing to do so will result in an unsafe vehicle.If installing these shafts with an OE steering box, you may need to trim the pin on the input shaft for U-joint clearance.Loctite 242, extra grease, and a torque wrench are highly recommended!!! |
| Description_DES |
Holley Steering Shaft Kit - 3rd Generation GM C10 Truck (Late) |
| Description_EXT |
Fits 1979-1987 GM C10 Trucks |
| Description_MKT |
These Holley steering shaft kits were designed to replace a worn stock one on your latter years' 3rd generation GM C10 trucks or with an engine swap where additional clearance may be needed. With sturdy DD-style steel shafts and dual u-joints, there is plenty of adjustability for your project to ensure everything is exact and safe. |
| Description_MKT |
*See Holley Part # 320-322 for 1973-1978 C10 Steering Shaft |
| Description_FAB |
Complete bolt-on solution with little or no modifications necessary depending on use |
| Description_FAB |
Eliminates factory rag joint providing a precise and responsive steering input |
| Description_FAB |
Will also work as a factory replacement steering shaft |
| Description_FAB |
E-Coat for maximum protection against corrosion |
| Description_FAB |
Steel construction with retaining screws on the bearing caps for strength and durability |
| Application |
1979-1987 GM C10 Trucks |
| Brand |
Holley |
| Category |
Steering |
| 17 |
Black |
| Emission Code |
5 |
| 1727 |
DD |
| 1728 |
DD |
| 200 |
Black E-Coat |
| 3390 |
Performance |
| 10 |
Steel |
| 30 |
Yes |
| part type |
Steering Shaft |
| Product Type |
Steering Shafts |
| Sub Category |
Steering, Gear and Related Components |
| 2343 |
Yes |
| Warning |
California Proposition 65 |